BikeParts Wiki

A "plain" seatpost (silver) connects the saddle to the frame (red).

File:Mountain Bike Seatpost.jpg

A microadjust seatpost (black) of a Trek Fuel 90 mountain bike.

File:Setback seatpost.JPG

A seatpost with a significant setback on a BMX bike.

A bicycle seatpost or seatpin[1] is a tube that extends upwards from the bicycle frame to the saddle. The amount that it extends out of the frame can usually be adjusted, and there is usually a mark that indicates the minimum insertion (or maximum extension). Seatposts can be made of steel, aluminum, titanium, carbon fiber, or aluminum wrapped in carbon fiber.[2]

Seatposts generally clamp onto saddle rails, while old or inexpensive seatposts slide into a separate clamp that then clamps the saddle rails.[3]


The size of the seatpost is dependent upon the internal dimensions of the seat tube of the bicycle frame. They come in various diameters, lengths and offsets. Offset is the distance between the centerline of the seatpost tube, and the centerline of the clamp area. Shims are often available to adapt a too-small seatpost to a too-large seat tube.


Diameters range from 22 mm to 32 mm. 27.2 is a common size for road bicycles. 25.4 mm (1 in) is a common size for BMX bikes. Documented sizes are almost always a multiple of 0.2 mm and include: 22.0, 22.2, 23.4, 23.8, 24.0, 25.0, 25.4, 25.8, 26.0, 26.2, 26.4, 26.6, 26.8, 27.0, 27.2, 27.4, 27.8, 28.0, 28.6, 29.4, 29.6, 29.8, 30.0, 30.4, 30.8, 30.9, 31.4, 31.6, 31.8, 32.


Lengths range from 75 mm to 430 mm. Mountain bike seatposts tend to be longer than road bicycle seatposts.


Offset or "layback" can range from 0 mm to 45 mm. A seatpost with offset is necessary when the seat tube angle of the frame is too steep to give the desired saddle setback (the horizontal distance between a plumb line hung from the nose of the saddle and the bottom bracket spindle). Conversely, an "in line" post may be required if the seat tube angle is too slack. Some saddles, notably Brooks leather saddles, have relatively short rails, allowing less adjustment of setback, and changing the seatpost may be the only way to achieve the correct position.



This type, usually found on older bikes, less expensive bikes, or kids bikes, consists of a tube which may decrease in diameter for the last inch or so (2.54 cm) and a separate clamping mechanism at the top. One bolt tightens the clamp to the rest of the seatpost and to the saddle rails at the same time.


This is the most common type found on bicycles today.[citation needed] They can be divided into two types; ones which can adjust the saddle angle continuously, and ones in which the saddle angle can only be adjusted to a certain number of positions.


Some high end road and track bicycle frames are made from one piece of molded carbon fiber with an integrated seatpost that is cut to length depending upon the rider, also known as a seat mast. The advantage is that it is lighter, can be molded into an aerodynamic shape, and removes the need to clamp an irregular tube shape. The disadvantage of this setup is that the seatpost height is not as adjustable. There is usually 2-3 centimeters of adjustment with the clamping device.


File:Aero seatpost.JPG

An aero seatpost in an aero seat tube help with two pinch bolts on an Orbea Ordu.

As alternatives to the integrated seatpost mentioned above, some seatposts merely have an aerodynamic shape that either matches the shape of the aero seat tube or is only not round above a certain point.[4] In the case of aero seat tubes, there are a variety of clamping mechanisms for such seatposts that include pinch bolts and wedges.


Suspension seatposts allow the saddle to move up and down with either a telescoping or parallelogram mechanism and incorporate a spring, an elastomer, or compressed air and possibly a damper to insulate against bumps. The preload of the spring may be adjustable. These seatposts are most common on hybrid and mountain bikes. Suspension seatposts usually come in fewer diameters, and shims are more likely to be necessary.


Pivotal seatposts are common on BMX bikes. They have a concave semicircle of ridges at their top that matches the convex semicircle of ridges on the bottom of a pivotal saddle. The two semicircles are held together with a bolt to attach the saddle to the seatpost.


Seatposts should be periodically removed from the frame, cleaned, greased and refitted to prevent the seatpost seizing in the frame. This is particularly important with bikes which do not have mudguards (fenders) that are regularly ridden in wet conditions.

There is some controversy about whether to grease carbon seatposts or not. There does not yet appear to be a consensus.[5][6] There are now specialty products, referred to as "carbon prep" or "carbon paste", specifically for the interface between carbon and most other materials.[7]


  1. Template:Cite web
  2. Template:Cite web
  3. Template:Cite web
  4. Template:Cite web
  5. Template:Cite web
  6. Template:Cite web
  7. Template:Cite web

External links[]

da:Sadelpind de:Sattelstütze es:Tija it:Reggisella pl:Sztyca rowerowa