View source for Bicycle chain

{{otheruses4|the drive chain on a bicycle|bicycle chain locks|Bicycle lock}}
[[Image:Chain.gif|frame|right|Roller chain and sprocket]]
[[Image:Shimano xt rear derailleur.jpg|right|150px|thumb|Bicycle chain snaking through a [[Derailleur gears|rear derailleur cage]] and over a rear sprocket]] 

A '''bicycle chain''' is a [[roller chain]] that transfers [[power (physics)|power]] from the [[Bicycle pedal|pedal]]s to the drive-[[Bicycle wheel|wheel]] of a [[bicycle]], thus propelling it. Most bicycle chains are made from [[steel|plain carbon]] or [[alloy steel]], but some are [[chrome-plated]] or [[stainless steel]] to prevent rust, or simply for aesthetics.

==History==
Obsolete chain designs previously used on bicycles included the [[block chain]], the [[skip-link chain]], and the [[Simpson Chain|Simpson lever chain]].  Most modern bicycle chains used with a single chainring and single rear sprocket are conventional industrial bushing chain.  Until the 1980s, most derailleur chains were also bushing chains, but today, virtually all derailleur chains are of the "Sedis" bushingless design. Compared to a bushing chain, a bushingless chain is cheaper to make, is less likely to break under shifting load, promotes better lubricant flow inside the rollers, and creates more lateral flexibility for multi-geared bicycles. However, it also wears much faster and has slightly worse mechanical efficiency than a bushing chain.

Before the [[safety bicycle]], bicycles did not have chains and the pedals were typically attached directly to the drive-wheel, thus limiting top speed by the diameter of the wheel and resulting in designs with front wheels as large as possible. Various linkage mechanisms were invented to raise the effective gear ratio, but with limited success.  Using  chain drive allowed the [[mechanical advantage]] between the drive and driven [[sprocket]]s to determine the maximum speed, thereby enabling manufacturers to reduce the size of the driving wheel for safety. It also allowed for the development of variable [[gear]]ing, allowing cyclists to adjust their [[Bicycle gearing|gearing]] to the difficulty of the terrain, on the fly.

==Efficiency==
A bicycle [[Roller chain|chain]] can be very efficient: one study reported efficiencies as high as 98.6%.<ref name="Spicer">{{cite web
| last = Spicer
| first = James
| title = Pedal Power Probe Shows Bicycles Waste Little Energy
| url = http://www.jhu.edu/news_info/news/home99/aug99/bike.html
| date = 1999-08-19
| accessdate = 2008-02-13}}</ref> Efficiency was not greatly affected by the state of lubrication.<ref name="Spicer" /> A larger sprocket will give a more efficient drive, reducing the movement angle of the links. Higher chain tension was found to be more efficient: "This is actually not in the direction you'd expect, based simply on friction".<ref name="Spicer" />

==Maintenance==
[[Image:Kettenschutz.png|thumb|Close-up of a utility bicycle's chain protected by a [[chain guard]]]]
How best to [[lubrication|lubricate]] a bicycle chain is a commonly debated question among cyclists.<ref name="Brown">{{cite web
| url = http://www.sheldonbrown.com/chains.html
| title = Sheldon Brown: Chain Maintenance
| accessdate = 2008-12-03}}</ref> Liquid lubricants penetrate to the inside of the links and are not easily displaced, but quickly attract dirt. "Dry" lubricants, often containing [[wax]] or [[Polytetrafluoroethylene|Teflon]], are transported by an evaporating [[solvent]], and stay cleaner in use. The cardinal rule for long chain life is never to lubricate a dirty chain, as this washes abrasive particles into the rollers.<ref name = "Brandt">{{cite web
| url = http://www.sheldonbrown.com/brandt/chain-care.html
| title = Chain care, wear and skipping 
| last = Brandt 
| first = Jobst
| accessdate = 2008-12-03}}</ref> Chains should be cleaned before lubrication. The chain should be wiped dry after the lubricant has had enough time to penetrate the links. An alternative approach is to change the (relatively cheap) chain very frequently; then proper care is less important.  Some [[utility bicycle]]s have fully-enclosing [[gear case|chain guard]]s which virtually eliminate chain wear and maintenance. On [[recumbent bicycle]]s the chain is often run through tubes to prevent it from picking up dirt, and to keep the cyclist's leg free from oil and dirt.

===Removal===
On most [[upright bicycle]]s, the chain loops through the right rear triangle made by the right chain stay, right seat stay, and seat tube. Thus a chain must be separated, "broken" is a term commonly used, with a [[chain tool]] or at a master link. A master link, also known as a connecting link, allows the chain to be inserted or removed with simpler tools, or even no tools, for cleaning or replacement.<ref name="Brown"/>

Some newer chain designs, such as [[Shimano]] and [[Campagnolo]] 10-speed chains, require a special replacement pin to be used when installing or reinstalling a separated chain. An alternative to this process is to install a master link, such as a [[SRAM Corporation|SRAM]] Power Link or a Wipperman Connex.<ref>{{cite web
| url = http://sheldonbrown.com/harris/chains.html
| title = Sheldon Brown: Chains from Harris Cyclery
| accessdate = 2008-12-03}}</ref>

==Wear==
Chain wear, or chain stretch, becomes an issue with extensive cycling. Although the overall effect is often called "stretch", chains generally wear through attrition of the bushings (or half-bushings, in the Sedis design) and '''not''' by elongation of the sideplates.  The [[tension (mechanics)|tension]] created by pedaling is insufficient to cause the latter. Because an old chain is longer than needed, its links will not precisely fit the spaces between teeth in the [[drivetrain]], making gear shifts a problem and possibly resulting in a 'skipping' chain that reduces power transfer and makes pedalling very uncomfortable.

Since chain wear is strongly aggravated by dirt getting into the links, the ''life time'' of a chain depends mostly on how well it is cleaned (and lubricated) and does not depend on the mechanical load.<ref name="Brandt"/> Therefore, well-groomed chains of high-power racing bicycles will often last much longer than those of a lightly used, but not so well cleaned city bike. Depending on use and cleaning, a chain can last only 1.000 km (e.g. in cross-country use, or all-weather abuse), 3.000 to 5.000 km for well-maintained derailer chains, or more than 6.000 km for perfectly groomed high-quality chains, single-gear, or hub-gear chains (preferably with a full cover [[chain guard]]).<ref>{{cite web
| url = http://www.kmcchain.com/index.php?ln=en&fn=service#4
| title = KMC: How to minimize chain wear
| accessdate = 2009-05-20}}</ref> 

Chain wear rates are highly variable, so replacement by calendar is likely to cause either needless chain replacement or continued use of a worn chain, damaging rear sprockets. One way to measure wear is with a ruler. Another is with a chain wear tool, which typically has a "tooth" of about the same size found on a sprocket. They are simply placed on a chain under light load and report a "go/no-go" result - if the tooth drops in all the way, the chain should be replaced.

Twenty half-links in a new chain measure 10" (254&nbsp;mm), and replacement is recommended before the old chain measures 256&nbsp;mm (0.7% wear)<ref name="Brown"/>. A safer time to replace a chain is when 24 half-links in the old chain measure 12<sup>1</sup>/<sub>16</sub> inches (0.5% wear). If the chain has worn beyond this limit, the rear [[sprocket]]s are also likely to wear, in extreme cases followed by the front chainrings. In this case, the 'skipping' mentioned above is liable to continue even after the chain is replaced, as the teeth of the sprockets will have become unevenly worn (in extreme cases, hook-shaped). Replacing worn sprocket cassettes and chainrings after missing the chain replacement window is much more expensive than simply replacing a worn chain in the first place.

==Sizes==
The chain in use on modern bicycles has a 1/2[[Inch|"]] pitch, which is [[ANSI]] standard #40, where the 4 indicates the pitch of the chain in eighths of an inch, and metric #8, where the 8 indicates the pitch in sixteenths of an inch.

===Width===
Chain comes in either 3/32", 1/8", 5/32" or 3/16" roller widths: 5/32" is used on cargo bikes and [[tricycle|trikes]], 1/8" with the common low cost coaster (back pedal brake) bike, [[hub gear|hub]] and [[fixed gear]]ing and on track bicycles, and 3/32" with the [[derailleur]] gears most commonly fitted on [[Racing bicycle|racing]], [[Touring bicycle|touring]] and [[mountain bike]]s.

The Wikibook, [http://en.wikibooks.org/wiki/Bicycles/Maintenance_and_Repair"Bicycle Maintenance and Repair"], explains that the difference between derailleur chains commonly labelled 8-speed, 9-speed, and 10-speed is in its external width (all are 3/32" chains).

===Length===
New chains usually come in a stock length, long enough for most upright bike applications. The appropriate number of links must be removed before installation in order for the drive train to function properly. The pin connecting links can be pushed out with a [[chain tool]] to shorten, and additional links may be added to lengthen.

In the case of [[derailleur gears]] the chain is usually long enough so that it can be shifted onto the largest front chain ring and the largest rear cog without jamming, and not so long that, when shifted onto the smallest front chain ring and the smallest rear cog, the rear derailleur cannot take up all the slack. Meeting both these requirements is only possible if the rear derailleur is compatible with the gear range being used on the bike.

In the case of [[single-speed bicycle]]s and [[hub gear]]s, the chain length must match the distance between crank and rear hub and the sizes of the front chain ring and rear cog. These bikes usually have some mechanism for small adjustments such as horizontal [[Dropout (bicycle part)|dropouts]], track ends, or an [[Eccentric (mechanism)|eccentric mechanism]] in the rear hub or the [[bottom bracket]]. In extreme cases, a chain half-link may be necessary.

==Variations==
In order to reduce weight, chains have been manufactured with hollow pins and with cut-outs in the links.  A few titanium chains have also been made, but while much lighter they are vastly more expensive, perhaps 10x the cost, and the titanium bearing surfaces reportedly wear quickly, leading to shortened life and reduced efficiency.

==Manufacturers==
Bicycle chains are made by companies such as:
*[[Campagnolo]]
*[[Rohloff AG]]
*KMC
*[[Shimano]]
*[[SRAM (bicycles)|SRAM]]
*Wippermann
*YABAN

==See also==
* [[Bicycle gearing]]
* [[Chain tool]]
* Other [[chainless bicycle]]s such as [[hydraulic bicycle]]s

==References==
{{Refimprove|date=February 2008}}
{{reflist}}

==External links==
*[http://www.epicidiot.com/sports/chain_length_calculator.htm Bicycle chain length calculator and stretch/wear test]
*[[b:Bicycles/Maintenance and Repair|Wikibooks Bicycle Maintenance and Repair]] - see the section on Chains
*[http://chain-guide.com/ The Complete Guide to Chain] - general, not specific to bicycles
*[http://bicycletutor.com/calculate-chain-length/ How to calculate chain length (video tutorial)]
*[http://www.youtube.com/watch?v=B2LhUvmUJXk Animation of Shimano gearing system]


[[Category:Chains]]
[[Category:Bicycle parts|Chain]]
[[Category:Mechanical power transmission]]
[[Category:Mechanical power control]]

[[cy:Cadwyn beic]]
[[de:Fahrradkette]]
[[fr:Chaîne (cyclisme)]]
[[id:Rantai sepeda]]
[[it:Catena (meccanica)#Bicicletta]]
[[nl:Fietsketting]]
[[pl:Łańcuch rowerowy]]
[[ru:Велосипедная трансмиссия]]